output specifications rr2-s03/d03 3 watt 2:1 regulated single & dual output absolute maximum ratings (4) 1) typical value at nominal input voltage and full load. 2) tested by nominal vin and constant resistor load. 3) measured input reflected ripple current with a simulated source inductance of 12uh. 4) exceeding the absolute ratings of the unit could cause damage. it is not allowed for continuous operating. 5) operation under no-load conditions will not damage these devices. however they may not meet all listed specifications. 6) its necessary to add a minimum capacitor in output for some models. please check single model datasheet for detail value. 7) input filter components are required to help meet conducted emission class a, which application refer to the emi filter of design & feature configuration. 8) an external filter capacitor is required if the module has to meet en 61000-4-4 and en61000-4-5. the filter capacitor we suggest: nippon-chemi-con ky series, 220 uf / 100v. dip 24, wide 2:1 input range full smd technology 1500 vdc isolation up to 3500 vdc isolation continuous short circuit protection efficiency up to 80% -25c~85c operation temperature range optional metal case voltage accuracy 1% line regulation 0.5% load regulation 0.5% ripple & noise (20 mhz bandwith) (1) 60 mv pk-pk short circuit protection continuous temperature coefficient 0.02%/c capacitor load (2) see table voltage range see table max. input current see table no-load input current see table input filter pi type input reflected ripple current (3) 35 ma pk-pk input specifications efficiency (typ.) see table i/o isolation voltage (3 sec.) input / output 1500 ~ 3500 vdc metal case / input & output 1000 vdc i/o isolation capacitance 60 pf typ. i/o isolation resistance 1000 m ohm switching frequency 100~400 khz humidity 95% rel. h reliability calculated mtbf (mil-hdbk-217f) > 2.199 mhrs. safety standard (designed to meet) iec 60950-1 general specifications case material non-conductive black plastic (ul94v-0 rated) nickel-coated copper base material non-conductive black plastic (ul94v-0 rated) pin material ? 0.5 mm brass solder-coated potting material epoxy (ul94v-0 rated) weight plastic 12.5 g, metal 15 g dimensions 1.25 x 0.8 x 0.4 physical specifications operating temperature (see derating curve) -40c~ 85c maximum case temperature 100c storage temperature -40c~125c cooling nature convection environment specifications note these are stress ratings. exposure of devices to any of these conditions may adversely affect long-term reliability. input voltage (100 ms) 5 modes -0.7 ~ 15 vdc 12 modes -0.7 ~ 24 vdc 24 modes -0.7 ~ 40 vdc 48 modes -0.7 ~ 80 vdc lead soldering temperature 260c (1.5 mm from case 10 sec.) all specifications typical at ta = 25c, nominal input voltage and full load unless otherwise specified. the information and specifications contained in this data sheet are believed to be correct at time of publication. however, we accept no responsibility for consequences arising from printing errors or inaccuracies. subject to change without notice. page: 1/3 last update: 21.07.09 emc specifications radiated emissions en55022 class a conducted emissions en55022 class a esd iec61000-4-2 perf. crit. b rs iec61000-4-3 perf. crit. a eft (8) iec61000-4-4 perf. crit. b surge (8) iec61000-4-5 perf. crit. b cs iec61000-4-6 perf. crit. a pfmf iec61000-4-8 perf. crit. a the models listed are just for standard type. if you need a special specification product, please contact our service. phone: +49 69 984047-0, mail to: info@rsg-electronic.de or use the forms on www.rsg-electronic.de (?kontakt).
rr2-s03/d03 3 watt 2:1 regulated single & dual output derating curve model number input input current (ma) output output current output current efficiency capacitor range no load/full load vdc min. load (ma) full load (ma) @fl (%) load ( hf) vdc RR2-0505S03AX 4.5-9 40 / 857 5 150 600 70 2200 rr2-0509s03ax 4.5-9 40 / 833 9 83.3 333 72 470 rr2-0512s03ax 4.5-9 40 / 810 12 62.5 250 74 470 rr2-0515s03ax 4.5-9 40 / 810 15 50 200 74 470 rr2-0524s03ax 4.5-9 40 / 857 24 31.3 125 70 220 rr2-0505d03ax 4.5-9 40 / 869 5 75 300 69 1000 rr2-0509d03ax 4.5-9 40 / 857 9 41.8 167 70 220 rr2-0512d03ax 4.5-9 40 / 833 12 31.3 125 72 220 rr2-0515d03ax 4.5-9 40 / 810 15 25 100 74 220 rr2-0524d03ax 4.5-9 40 / 857 24 15.8 63 70 100 rr2-1205s03ax 9-18 20 / 328 5 150 600 76 2200 rr2-1209s03ax 9-18 20 / 324 9 83.3 333 77 470 rr2-1212s03ax 9-18 20 / 316 12 62.5 250 79 470 rr2-1215s03ax 9-18 20 / 316 15 50 200 79 470 rr2-1224s03ax 9-18 20 / 316 24 31.3 125 79 220 rr2-1205d03ax 9-18 20 / 324 5 75 300 77 1000 rr2-1209d03ax 9-18 20 / 320 9 41.8 167 78 220 rr2-1212d03ax 9-18 20 / 320 12 31.3 125 78 220 rr2-1215d03ax 9-18 20 / 320 15 25 100 78 220 rr2-1224d03ax 9-18 20 / 320 24 15.8 63 78 100 rr2-2405s03ax 18-36 12 / 156 5 150 600 80 2200 rr2-2409s03ax 18-36 12 / 156 9 83.3 333 80 470 rr2-2412s03ax 18-36 12 / 152 12 62.5 250 82 470 rr2-2415s03ax 18-36 12 / 152 15 50 200 82 470 rr2-2424s03ax 18-36 12 / 156 24 31.3 125 80 220 rr2-2405d03ax 18-36 12 / 160 5 75 300 78 1000 rr2-2409d03ax 18-36 12 / 158 9 41.8 167 79 220 rr2-2412d03ax 18-36 12 / 156 12 31.3 125 80 220 rr2-2415d03ax 18-36 12 / 156 15 25 100 80 220 rr2-2424d03ax 18-36 12 / 156 24 15.8 63 80 100 rr2-4805s03ax 36-72 8 / 81 5 150 600 77 2200 rr2-4809s03ax 36-72 8 / 80 9 83.3 333 78 470 rr2-4812s03ax 36-72 8 / 78 12 62.5 250 80 470 rr2-4815s03ax 36-72 8 / 78 15 50 200 80 470 rr2-4824s03ax 36-72 8 / 78 24 31.3 125 80 220 rr2-4805d03ax 36-72 8 / 80 5 75 300 78 1000 rr2-4809d03ax 36-72 8 / 79 9 41.8 167 79 220 rr2-4812d03ax 36-72 8 / 78 12 31.3 125 80 220 rr2-4815d03ax 36-72 8 / 78 15 25 100 80 220 rr2-4824d03ax 36-72 8 / 78 24 15.8 63 80 100 model selection guide page: 2/3 last update: 21.07.09 number structure isolation 1=1.5 kvdc 3=3.5 kvdc power 03=3w output 05=5v 09=9v 12=12v 15=15v 24=24v code internal rr2 - xx xx s 03 a 1 (m) type s=single d=dual input 05=4.5~9v 12=9~18v 24=18~36v 48=36~72v name/package rr2=dil24 add suffix ?m for metal case! if no suffix mean plastic case.
mechanical specifications standard rr2-s03/d03 3 watt 2:1 regulated single & dual output page: 3/3 last update: 21.07.09 mail: info@rsg-electronic.de www.rsg-electronic.de rsg electronic components gmbh sprendlinger landstr. 115 d-63069 offenbach tel. +49 69 984047-0 fax +49 69 984047-77 rsg rr2-xxxxx03ax mechanical specifications metal case rsg rr2-xxxxx03axm 24 pin dil package nickel coated copper ?m case 24 pin dil package non-conductive plastic all dimensions are typical in millimeters (inches). 1) pin diameter: 0.5 0.05 (0.02 0.002) 2) pin pitch tolerance: 0.35 ( 0.014) 3) case tolerance: 0.5 ( 0.02) all dimensions are typical in millimeters (inches). 1) pin diameter: 0.5 0.05 (0.02 0.002) 2) pin pitch tolerance: 0.35 ( 0.014) 3) case tolerance: 0.5 ( 0.02) emi filter input filter components (c1, l) are used to help meet conducted emissions requirement for the module. these components should be mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise. test configurations rr2-05xxxxx rr2-12xxxxx rr2-24xxxxx rr2-48xxxxx pin # single dual single-3 dual-3 pin connections
|
